Matt Filipski, my first student at Littleton Common Makers, tests out a chisel he's learning to sharpen by hand on oilstones.
I'm very excited to announce that Littleton Common Makers is now open! This is the makerspace I first wrote about in this blog post.
The purpose of a makerspace is to provide a workspace and community for people who like to make things, but don't have space or equipment of their own to do it. This covers the whole range of making, from low-tech to high-tech, for hobbyists and professionals.
One of the real values in a makerspace is that it provides access to a number of disciplines and facilitates cross-pollination across them. This includes electronics, robotics, woodworking, metalworking, fabric arts, plastics, leather, jewelry making, the list is endless.
Littleton Common Makers (LCM) is available for member use, with classes open to the general public. It's currently limited to age 18 and above. It's an evolving work in progress, so capabilities and options will change over time.
All the credit for making this happen goes to my friend Faisal Mohammed. He had the dream and put in all the work to find a space, pay the rent, secure insurance and other paperwork, organize and administer membership, and prepare everything for use. He's the one who's made the initial investment in this community resource. The more of us who join him, the better it will be!
The Littleton Common Makers website is www.LCMakers.com. Like LCM itself, the website is a work in progress. For all inquiries, send email to info@LCMakers.com.
The Lowell Sun has also published a nice article about Faisal and LCM here.
Littleton Common Makers is located in The Littleton Mill, just off Littleton Common, at 410 Great Rd, Littleton, MA, right by the Rt. 119 exit off Interstate 495 (map here).
The main parking lot is near the traffic light at the eastern end of the 495 overpass. There are a number of entrances to the building. The proper one to reach LCM is up the small outside stairwell with the signs for Dolphin Insulation, New England Yoga, and Indoor Batting Cages.
Look for the second-floor entrance from the deck at the top of these stairs from the parking lot.
It's a maze inside to reach the space, so look for the signs to Littleton Common Makers. From the entrance:
- Go straight to the end of the hall, past the batting cages on the right.
- Turn left.
- Go to the end of the hall, through a small tunnel into the older building.
- At the Victory Liberty Loan poster go up the stairs on the right.
- At the top of the stairs turn left and left again to the hall behind the stairs.
- Turn left again.
- Head in the direction away from the orange double doors.
- Head to the end of the hall.
- Go up the stairs.
- At the top of the stairs turn right.
- Head to the red double doors.
- LCM is the white door to the right of the red double doors.
Faisal has a standing open house at LCM every Thursday from 6-8pm. (subject to cancellation, check www.LCMakers.com or send email to info@LCMakers.com to confirm).
A variety of equipment covering a range of maker disciplines and crafts is available for use by anyone who has completed the required training and been checked off in its use.
Some equipment has metered usage to ensure fair access and manage wear and duty cycle. Some has associated materials cost.
Training classes will be offered at modest cost to ensure proper usage to avoid injury or damage.
Current equipment includes:
- Woodworking hand tools
- Electronics worktable
- Laser cutter
- 3D printer
- Sewing machine
Is there some equipment you'd like to place at Littleton Common Makers? If so, you should consider becoming a member!
Membership is on a monthly basis, payable by credit card online via Square, or by check. Depending on membership level, members enjoy access to the space (controlled by RFID key), storage, time allotments and discounts on metered equipment, and discounts on classes.
There are currently three levels:
- Full membership, $75/month. This offers 24/7 access, with storage.
- Partial membership, $50/month. This offers limited access (weekdays 6-8pm, weekends 9am-5pm), and no storage (all work is "bring in, take out").
- Military and emergency personnel discount membership available.
Note that partial member hours will expand as membership grows, since a full member must be present.
I've moved my four Paul Sellers-style student workbenches out of my basement workshop to the space, and once I get fully organized, I'll have all of my student tools there as well.
This means that these tools will also be available to members who have completed training. I offer the following training class:
- 3 hours of hands-on instruction for $64 (includes $10 materials fee).
- An additional hour of hands-on practice time is available for $18.
- Covers basic use and handling of the following unpowered hand tools:
- Workbench and work-holding
- Handplanes (including router plane)
- Measuring and marking tools
- Sharpening tools
Other instructors will be offering classes in their areas of expertise. As noted above, some of these classes are required before you are allowed to use the covered equipment.
Is there a class you'd like to teach at Littleton Common Makers? If so, you should consider becoming a member!
About The Location
Faisal working at the electronics table. The windows to his right look out onto the IBM building.
Matt working at the workbenches. The windows behind him look out toward Littleton Common.
The laser cutter with some laser-cut and laser-engraved wooden parts. This vents exhaust smoke out a tube in the window, an example of why you need a workshop to use this kind of equipments.
Faisal's original plan was to have the space in Ayer, because wouldn't it be great if it was 5 minutes from home? Unfortunately, there was no suitable venue that was affordable for a budding makerspace. By necessity it has to start small, then grow with success. Fortunately, Littleton is the next town over, so it's just another 7 minutes down the road.
The Littleton Mill is an old mill complex that's been converted into mixed use suites. Other occupants include a community theater, various one-room workshops and studios, small manufacturers, even indoor batting cages! Like all such old mills throughout New England, the place is a maze of buildings of various vintage, corridors, and stairwells, so it's easy to get lost.
I actually used to work right across the street back in the 90's at the King St. Digital Equipment Corporation facility (old DECcies still fondly refer to it as LKG). That later became Compaq, then HP, and is now IBM (you can see it from the makerspace's north-side windows). Ironically, Faisal is an engineer at a company in another old mill related to DEC, Clocktower Place in Maynard, MA. Known simply as "the mill", this was DEC's headquarters from 1957 to 1992. This area is a major part of the Boston 495 high tech corridor.
The building already has a well-established woodworking presence: my friend Freddy Roman, professional woodworker and restorer, has his workshop downstairs. I wrote a profile of Freddy several years ago here. At that time, he was sharing another suite in the building with renowned woodworker Will Neptune. Prior to Freddy and Will, that workshop was occupied by guitar-maker Julius Borges.
If you live in the area and are interested in tinkering with some of these things, join LCM or take some classes there!